
Blow out your own sprinklers, or hire it out?
Reviewed by Adam Hurlbert, Owner & Founder, 15+ years in landscape & property care
You can winterize your own sprinklers if you have a compressor that can keep up, you know what your pipe is made of and keep the pressure under its limit, you can connect downstream of the backflow preventer rather than through it, and you wear eye protection. If any of those is a guess, hiring it out costs less than a split backflow preventer in April. And if your system was built with drain valves at its low points, it may be designed to drain without a compressor at all. Here is how to decide.
What does a blowout actually involve?
The water supply to the system is shut off. A compressor is connected at a blowout fitting downstream of the backflow preventer, so the air never goes through the device. Then each zone is opened in turn and air pushes the water out through the heads until only mist and then air come out. Manual drains are opened where the system has them, the backflow preventer is drained and left the way its design calls for, and the controller is shut down. That is how we do it, and where the system's configuration allows, we also drain the supply piping from inside the house.
Our guide to winterizing your sprinkler system covers the steps and the timing in detail. This page is about whether to do it yourself.
Do you need a compressor at all?
Not every system is built to be blown out. Some were installed with manual or automatic drain valves at the low points, so they drain by gravity when the water is shut off. If yours is one of them, follow the way it was designed: shut off the supply, open the drains, and make sure every low point actually empties. Be honest about whether it does, though. Colorado State University Extension notes that drain valves rely on gravity and describes compressed air as the method that lets you confirm the water is cleared. Most systems were not built with drains at every low point, and water left in a low spot, a valve or a head is exactly where freeze cracks start.
What can go wrong doing it yourself?
Most DIY damage comes from a short list of mistakes. Blowing air through the backflow preventer: CSU says pressure vacuum breakers and reduced pressure devices must never be blown out with compressed air, because the heat can melt their rubber seals. Too much pressure: CSU puts the maximum at 80 psi for rigid PVC pipe and 50 psi for polyethylene, and warns that excess pressure can blow nozzles off and cause other damage. Running air through too few open heads for too long, which CSU warns can heat pipe and fittings to the point of melting. And eye injuries, which is why the same guidance says to wear proper eye protection.
The quieter mistake is stopping too soon. A zone that still spits water when you move on will hold water in its low spots, and a small home compressor can struggle to keep enough air moving to clear a long zone.
What about the backflow preventer itself?
It usually sits above ground where the irrigation line leaves the house supply, so it is exposed to the cold in a way buried pipe is not. Drain it, and leave its valves as the manufacturer or your installer recommends; CSU notes that leaving the valves half open helps keep the backflow preventer from freezing and splitting, while fully open or fully closed valves can trap water. In Missoula, a backflow assembly that has to be repaired or replaced must then be tested by a certified tester before it goes back into service, so a freeze crack costs a repair and a test.
When is doing it yourself a reasonable choice?
When the system is small, you know what pipe it uses, it has an accessible blowout fitting downstream of the backflow preventer, you have a compressor that can keep up and a way to set its pressure, and ideally you have watched it done properly once. Plenty of homeowners winterize their own systems every year without trouble. If that is you, keep doing it, and keep notes on which zone takes longest so next year is faster.
When is hiring it out the better call?
When the system has no blowout fitting and you would be improvising a connection, when you do not know the pipe type, when the compressor you have is a small one, or when the system is large, has several controllers, or serves a commercial property, an HOA or a rental. Those take longer and are worth booking early. Hiring it out also makes sense when the timing is the problem: the first hard freeze across the valley generally comes between late September and October, and a blowout done after it is too late.
What if you already missed the freeze?
Do not run the system to check it in the middle of winter. Blow it out as soon as you can on a day above freezing, and plan a careful spring startup to find any damage before the season starts. Our spring sprinkler startup guide covers the order.
How do the costs compare?
Doing it yourself costs your time and, if you do not own one, the use of a suitable compressor. Hiring it out costs a service visit. The real comparison is with the repair you are trying to avoid: split pipe, cracked valves and a damaged backflow preventer found in spring, plus a backflow test after the repair. If you are confident in the steps and the equipment, DIY is fine. If you are not, the visit is the cheaper side of the bet. For what repairs involve, see what moves the price of a sprinkler repair.
Next, see our sprinkler blowout and winterization service, book a blowout, or call HJ Property Care & Tree Service at (406) 215-7319. For the rest of the property, start with the Montana Property Care Guide.
Need help?
HJ Property Care & Tree Service is locally owned and ISA-certified. Call for a free estimate.
This article is part of the Montana Landscaping, Lawn & Irrigation Guide, our complete guide for western Montana property owners.
Explore our irrigation systems.
Sources
We cite primary sources: Montana State University Extension, the City of Missoula, and the ISA, so you can verify anything here yourself.
- Home Sprinkler Systems: Preparing Your Sprinkler System for Winter (Colorado State University Extension). Last checked November 11, 2026.
- Public Works Standards Manual Appendix 4-A, Cross-Connection/Backflow Protection Program (City of Missoula / Missoula Water). Last checked November 11, 2026.
Ready to transform your outdoor space?
Get a free, no-obligation estimate within 48 hours. Locally owned and ISA-certified.
